| |
|
Description |
Unit |
Single Layer |
Double Layer |
|
Screw
Dia |
MM |
100 (with grooved barrel) |
100+70 (with grooved barrel) |
|
Plasticizing Capacity |
kg/hr |
300 to 350 |
300 to 350+90 to 100 |
|
Accumulator Capacity |
Kg |
36 |
30+12 |
|
L/D
ratio |
|
28 |
28 |
|
Max.
Daylight opening |
MM |
3000 |
3000 |
|
Min.
Daylight opening |
MM |
1800 |
1800 |
|
Max.
mould size with tie rod (WxH) |
MM |
1500
Í
2000 |
1500
Í
2000 |
|
Screw
drive motor |
HP |
100 |
100+40 |
|
Hyd.
Motor (main) |
HP |
60 |
60 |
|
Heating
load |
KW |
100 |
435 |
|
Total
connected load |
HP/KW |
325/244 |
393/295 |
Rate of
production:
• 2000 ltr. tank
• 1000 ltr. tank |
Per/hr
Per/hr |
8 to 10
15 to 16 |
10 to 12
18 to 20 |
Approx
weight of W.S.T.
• 1000 ltr.
• 2000 ltr. |
kg.
kg. |
16
30 |
15
28 |
|
|
|
| |
|
COMPARISON BETWEEN ROTO MOULD
AND BLOW MOULD |
| |
|
SR. No. |
Roto Moulding |
Blow Moulding |
|
1 |
Material out of L.D. therefore
strength is less |
Material out of HM so strength is
high |
|
2 |
Product weight is high
2000 ltr tank wt. 46 kg
1000 ltr tank wt. 26 kg |
Lower weight than Roto
2000 ltr tank wt. - 28 - 30 kg
1000 ltr tank wt. - 16 - 17 kg |
|
3 |
Production is very slow
24 tank / 24 hrs of 2000 ltr. |
Production is 10 to 12 times high
12-15 tanks / hr |
|
4 |
Pulversing & Pelletising process is
required |
It is nit required in Blow Moulding |
|
5 |
You should have seperate moulds for
each size |
3/4 in one moulds are possible |
|
| |
| |
|
Product range - |
| |
|
1. Loft Tanks : 350 ltrs to 1000
ltrs
2 Overhead tanks : 500 ltrs to
2500 ltrs
3. 1000 ltr intermediate Bulk
Container (IBC)
This cube-shaped, 1000 litre
capacity intermediate bulk
container (IBC) is used
worldwide for the transport of
industrial chemicals,
lubricants, agricultural
chemicals and liquid food
products. Its basic components
are an inner container blow
moulded from high molecular
weight high-density
polyethylene, an outer case
fabricated from galvanized steel
and both mounted on a 4-way
entry palette for fast handling
by fork lift. A filling opening
of about 150 mm on the center of
top surface and discharge valve
at bottom of one side is
provided for quick and efficient
filling & discharging |
| |
|
|
|
Advantages: |
|
|
-
Containers with high
packaging volumes lower
costs tanks to the following
advantages.
-
Reduced filling, sealing,
labeling times
-
Maximum usage of storage
space
-
Multi trip use of containers
-
Efficient discharge
-
Lower cost
|
